flexible asphalt Waterproof Sheet Material

Short Description:

Quick Details Type: Waterproof Membrane Place of Origin: Hebei, China (Mainland) Brand Name: JIELANGTE Model Number: SBS Color: Black ...

Product Detail

Product Tags

Quick Details

  • Type: Waterproof Membrane
  • Place of Origin: Hebei, China (Mainland)
  • Brand Name: JIELANGTE
  • Model Number: SBS
  • Color: Black
  • Thickness: 1.5MM-5MM
  • Length: 10m/roll
  • Width: 1-2m
  • Application: roof,subway,basement,wall,pool,etc
  • Surface material: PE film, Aluminum foil,Sand, Schist flake,etc
  • Tire: Polyester, Glass fiber
  • Pull strength: 500N/5cm
  • Inforcement: polyester or fiberglass
  • Modified Materials: SBS/APP

Packaging & Delivery

Packaging Details According to your requirements
Delivery Time 10 days upon receiving order

Flexible asphalt Waterproof Sheet Material


Self adhesive waterproof membrane is produced with SBS elastomer and bitumen as raw materials, using polyethylene film. Aluminum foil, PP fabrics, sand coated on the upward or no file(both side self-adhesive) while self-adhesive protection layer on the downward surface. It has a widely prospect new construction waterproof materials. Good self-adhesion, no leaking, cold flexibility, especially in self-adhesion. That is unique product in waterproof and application.


1. No use of fire and no environment pollution, It is an environmental product.
2. large tensile strength, elongation and tear strength.
3. strong adaptable to weather conditions
4. It has good cohesiveness


Technique data




Construction procedure and attention:
1)Basic cleaning
Clean up debris, level off if there are sharp bump, it may construct without water , moisture is allow.?
2)Pave the waterproofing sheet membrane
spread over the waterproof sheet membrane with the particles facing on the basement,When paving the adjacent sheet membrane. pay attention to overlap the edge alignment to keep the overlap without any gap.
3)overlap joint waterproof sheet membrane
(1) overlap waterproof sheet membrane:Tear off the Isolation membrane of the Double-side self-adhesive of polymer down surface,Remove tape rolling again after isolation film on the surface,And connected to the coil will take to paste on the tape, strong crush of binding, when necessary to tape appropriate heating, paste the effect is more ideal.more adept to dry conditions shall apply.
(2) overlap joint waterproofing sheet membrane: Shovel glue stick tape after lap, this approach is applicable to the waterproof layer may be rain water.
(3) Butt joint waterproof sheet membrane :D ocking coil binding material adopt DNM coil,Coil cut into strip and place the glue face up, trea off the surface after isolation membrane, paste the upper butt of the coil, and strong crush of binding. the approach is suitable for the waterproof layer may be rain water, can avoid so release.
4)Seal the deal:?DNM roll angle of yin and Yang and the node does not need additional layer construction, but large coil shop paste is completed after node to deal with the details of the structure is complete and the tightness of the check processing, aiming at the pile head on the floor of the basement, bolt, drains and other details, should adopt consolidates with adhesive tape, then brush waterproof coating to seal the deal.
5)organization acceptance
6)Subsequent construction: to complete the construction of waterproof layer, can be reinforced concrete binding.




1. Balcony, bathroom, kitchen
2. Tunnels, Industrial roofs
3. Flat and sloped roofs
4. Basements, Foundation and retaining walls
5. Gardens, Bridges



Place the membrane vertically.
Packed with strong wood pallet and covered by shrink film in case of slant
Keep away from fire during storage and transportation.
Membranes should be stored under dry and ventilated conditions in order to keep away from sunlight and raining.









  • Previous:
  • Next:

  • Related Products

    WhatsApp Online Chat !